The more absorbed light will lead to more charges and therefore increasing the I sc. The reason for the increase in FF can be attributed to the increased R sh as discussed above

compared to the cells without CdS. For the ITO/nc-TiO2/CdS(n)/P3HT:PCBM/Ag cells, however, with the increase of CdS LGX818 in vitro cycle number n from 5 to 15, the V oc decreased from 0.6 to 0.33 V. The I sc decreased from 5.81 to 4.9 mA/cm2 and the FF decreased from 0.50 to about 0.36. These results might be caused by the increased roughness of the ITO/nc-TiO2/CdS(n)/P3HT:PCBM/Ag cells with the increase in cycle number n. On one hand, the CdS nanocrystalline film can prevent the charge transfer back from TiO2 to the P3HT:PCBM film. On the other hand, the increased absorption selleck compound amount of CdS will increase the roughness of the ITO/nc-TiO2/CdS films as shown in Figure 2, which might lead to form small CdS nanoparticle islands instead of a uniform film. Some of these islands may not be fully covered by the P3HT:PCBM film, which leads to increased leakage current in the cells and therefore decreasing the V oc and I sc. The decrease in FF may be due to the reduced R sh, which decreased from about 67 to about 21 Ω/cm2 with the increase of n from 5 to 10 (Figure 5). Finally, the PCE of the ITO/nc-TiO2/CdS(n)/P3HT:PCBM/Ag

cells decreased from 1.57% to 0.61% (Table 1), which is still higher than that (0.15%) of the ITO/nc-TiO2/P3HT:PCBM/Ag cell. Nonetheless, our results clearly show that the PCE of the ITO/nc-TiO2/CdS(n)/P3HT:PCBM/Ag

cells increased significantly by depositing CdS on TiO2. The best PCE of 1.57% for the ITO/nc-TiO2/CdS(5)/P3HT:PCBM/Ag cell is achieved, which is about ten times that (0.15%) of the ITO/nc-TiO2/P3HT:PCBM/Ag cell. To sum up, the three main reasons for the improved efficiency of the ITO/nc-TiO2/CdS/P3HT:PCBM/Ag cells are as follows: first, the absorbance of the spectra of the ITO/nc-TiO2/CdS/P3HT:PCBM film increased significantly due to the deposited CdS QDs; second, the deposited CdS layer between the nc-TiO2 and active layer (P3HT:PCBM) can reduce the charge recombination as an energy barrier Cyclin-dependent kinase 3 layer; and third, the interfacial area increased due to the increased roughness of the ITO/nc-TiO2/CdS film compared to the ITO/nc-TiO2 without CdS QDs, which makes more excitons click here dissociate into free electrons and holes at the P3HT/CdS and P3HT/TiO2 interfaces. According to the above results, it should be expected that the efficiency of the ITO/nc-TiO2/CdS/P3HT:PCBM/Ag cell can be further improved by inserting interfacial layer materials such as PEDOT:PSS between the P3HT/PCBM layer and the anode (Ag). As an example, the I-V characteristics of the best ITO/nc-TiO2/P3HT:PCBM/PEDOT:PSS/Ag and ITO/nc-TiO2/CdS(5)/P3HT:PCBM/PEDOT:PSS/Ag devices under an AM 1.5G (100 mW/cm2) condition and in the dark are shown in Figure 6.